Free Mp3 Ringtones

[defgf24uw]

Yarn Uster statistics of system control


Production practice proves that the medium and long-spun yarn unevenness and some fragments produced in long segments of uneven spinning drafting assembly (continued on page 21) March 2001 (1) Heilongjiang Textile 2l mouth, as far as possible to drive on canvas not thin dense road. Multi-site inspections warp Tenders found arbitrary line, hairiness promptly removed, reducing the frequency of stopping sets,[link widoczny dla zalogowanych], is equivalent to thin dense way to reduce the opportunities, and improve production efficiency l 『. Requirements for workers to do a good job on the off-axis by, weft, shuttle changing,[link widoczny dla zalogowanych], air shuttle, shuttle rolled off the car's head and out of maintenance and collision location and space, while the level of support tray to be consistent on both sides, and roll-off maintenance to take part, check the prop shaft clip foot reed with reed clip axis gap is qualified, the reed is loose, the angle is appropriate, whether high or low hanging fully meet the requirements, both sides are the same, whether the medium with tension hanging comprehensive, integrated clip is complete . Required to remove the workers follow the rules. 2.2 The equipment units in order to reduce the frequency of stops, the work required to conduct a wide range of security, maintenance, operation head of the flat parts of the truck on the shuttle to the lighting channel, scheduled to hit Tsui reed nose contact time with the same gap line K23 cores should pay particular attention to the same degree of wear, the big to replace. Folder in the reed shaft and foot care (K26) to maintain the gap in 0.8rm 'n, reed folder should be overrun shaft wear welding and lathe trimmed by use of foot care to wear a serious book with nylon pad chip approach, which reached the installation standards. 2.3 The opening time on the thin weft technique have some influence in the development process when the appropriate consideration. Warp tension on the machine should be appropriate, should not be too large or too small. On the lower ground warp yarn is not the case take the shuttle plate, integrated low-hanging as much as possible,[link widoczny dla zalogowanych], but also to ensure the integrated elastic suspension medium, do not shake, healds flexible, so that smaller upper warp tension,[link widoczny dla zalogowanych], the yarn around the course in beating traverse a little to compensate for the thin yarn and fabric space for larger defects on the plane tension, which is equivalent to reducing the tension on the underlying differences in the warp, weft prone to dilute. Too much tension on the machine will be increased by the breakage, stop Taiwan and generate opportunities thin dense road Tension can not be too small, too small is not conducive to speak clearly and can not maintain the normal pieces of cloth in the machine 2.4 Management Strengthening equipment maintenance and management work (normal size flat car and the maintenance cycle), according to quality standards inspection and acceptance, the set of all in good condition. Strengthen the management of the shuttle and the shuttle repair with better control latitude, to reduce the resulting internal quality shuttle weft break. Designated person and the maintenance of peace after the car without driving thin machine weft-by-station inspection. Weft stop Taiwan if b is failure to set a target, zoning responsibility system. Above were included in the assessment of economic responsibility through the implementation of the above 3 Conclusion of scientific management, significantly dilute latitude than the previous downward trend, which improve product quality and production efficiency play a greater role from the original thin latitude 41.2 % to 20.8%, the plane first-class product rate than before l】%, fabric quality has improved significantly. Thus, only the use of scientific management, to find its own deficiencies, to make our plant an early stand among the advanced countries the national textile enterprises Received Date: 2O00-04-13 (on the wall, then the first page) after the area, and video mainly produced in the spinning section of irregularity of the anterior distraction device, so the former should pay attention to the jaw area after the district should pay attention to gauge and pull winding process (1332 [\The cone yarn neps neps than the spinning tube increases, generally about 20% can increase the metal groove grooved drum briefly slightly lower than the Bakelite. Stretch factor, roving twist factor, pressure gauge plastic. Yarn quality indicators are as follows (example yarn export C194c) 6 Conclusion (1) yarn quality control is good or bad, not only for the spinning process, after an impact, but the main reflects the level of production of advanced spinning or not, is a comprehensive reflection of spinning. (2) CV% value of dry, detail, thick and thin fibers arranged mainly by confusion, distraction uneven, causing the accumulation of short fiber: mainly by the random fiber neps, fiber hoe up soil around plants with cuttings produced, in addition to the quality of raw materials and outside the cotton gin , also effectively ruled out spinning grow less and accident related. (3) control yarn nep is one of the key raw material quality,[link widoczny dla zalogowanych], the second carding process configuration, in which the most important quality clothing. Control yarn Uster CV% value lies in the spinning process, while semi-finished products quality can not be ignored. (4) control should be improved yarn quality fiber separation, straight inner structure of parallelism and other semi started to reduce the accumulation of short fiber and improve the drafting uneven, reducing the growth of winding process. (5) yarn quality control is a systematic project, to produce high-quality yarn, we must first consider the quality of raw materials situation, and then consider the relevant material processes rubidium yarn processing equipment conditions. Received date: 2000 A l1-20
More articles related to topics：


[link widoczny dla zalogowanych]

[link widoczny dla zalogowanych]

[link widoczny dla zalogowanych]